ALL-INCLUSIVE VAPORIZER

FILL INSTRUCTIONS

For adult use only.

Language >English | Deutsche | Français | Español
Language: English
Deutsche
– Coming Soon

Français
– Coming Soon

Español
– Coming Soon

ALL-INCLUSIVE VAPORIZER

FILL INSTRUCTIONS

For adult use only.

Listo™

Fill Instructions

Filling the Reservoir

Step One: Fill a syringe with a short, blunt tipped needle (14 ga. or smaller) with oil. Insert the needle into the space between the airway and the outer walls of the cartridge reservoir. Fill both sides of the cartridge with 1mL of oil (0.5mL for each side).

Note: The syringe and needle may need to be warmed to improve fluid flow.

Do not allow fluid to enter the airway (center tube) as it may cause a short circuit.

Checking the Silicone Ring

Step Two: Check the silicone sealing ring is set properly in the mouthpiece. Make sure the silicone seal is well-placed before fitting the mouthpiece on the device.

Capping the Cartridge

Step Three: Place the mouthpiece on top of the device, align to the device walls, and press the mouthpiece in until proper closure.

Failure to install the mouthpiece within 1 minute of filling may result in leakage.

Allow For Headspace

Step Four: Check that the mouthpiece is pressed in completely and properly.

Device should be allowed to stand for at least 30 minutes before use. During this time, fluid is priming the atomizer. The rate that the atomizer saturates is dependent upon the viscosity of the fluid. More viscous fluids may require more time.

If the device is to experience a pressure change as a result of an increase in temperature or a change in elevation, the device must be shipped with the mouthpiece facing down, allowing for the inlets to be exposed to ambient air. ​

Previous
Next

Infinity™

Fill Instructions

Filling the Reservoir

Step One: Fill a syringe with a short, blunt tipped needle (14 ga. or smaller) with oil. Insert the needle into the space between the airway and the outer walls of the cartridge reservoir. Fill both sides of the cartridge with 0.5mL of oil (0.25mL on each side).

Note: The syringe and needle may need to be warmed to improve fluid.

Do not allow fluid to enter the airway (center tube) as it may cause a short circuit.

Capping the Cartridge

Step Three: Place the mouthpiece on top of the device, align to the device walls, and press the mouthpiece in until proper closure.

Failure to install the mouthpiece within 1 minute of filling may result in leakage.

Allow For Headspace

Step Four: Check that the mouthpiece is pressed in completely and properly.

Device should be allowed to stand for at least 30 minutes before use. During this time, fluid is priming the atomizer. The rate that the atomizer saturates is dependent upon the viscosity of the fluid. More viscous fluids may require more time.

If the device is to experience a pressure change as a result of an increase in temperature or a change in elevation, the device must be shipped with the mouthpiece facing down, allowing for the inlets to be exposed to ambient air. ​

Previous
Next

Poché™

Fill Instructions

Filling the Reservoir

Step One: Fill a syringe with a short, blunt tipped needle (14 ga. or smaller) with oil. Insert the needle into the space between the airway and the outer walls of the cartridge reservoir. Fill both sides of the cartridge with 0.5mL of oil (0.25mL on each side).

Note: The syringe and needle may need to be warmed to improve fluid.

Do not allow fluid to enter the airway (center tube) as it may cause a short circuit.

Checking the Silicone Ring

Step Two: Check the silicone sealing ring is set properly in the mouthpiece. Make sure the silicone seal is well-placed before fitting the mouthpiece on the device.

Capping the Cartridge

Step Three: Place the mouthpiece on top of the device, align to the device walls, and press the mouthpiece in until proper closure.

Failure to install the mouthpiece within 1 minute of filling may result in leakage.

Allow For Headspace

Step Four: Check that the mouthpiece is pressed in completely and properly.

Device should be allowed to stand for at least 30 minutes before use. During this time, fluid is priming the atomizer. The rate that the atomizer saturates is dependent upon the viscosity of the fluid. More viscous fluids may require more time.

If the device is to experience a pressure change as a result of an increase in temperature or a change in elevation, the device must be shipped with the mouthpiece facing down, allowing for the inlets to be exposed to ambient air. ​

Previous
Next

Owa™

Fill Instructions

Filling the Reservoir

Step One: Fill a syringe with a short, blunt tipped needle (14 ga. or smaller) with oil. Insert the needle into the space between the airway and the outer walls of the cartridge reservoir. Fill both sides of the cartridge with 0.5mL of oil (0.25mL on each side).

Note: The syringe and needle may need to be warmed to improve fluid.

Do not allow fluid to enter the airway (center tube) as it may cause a short circuit.

Checking the Silicone Ring

Step Two: Check the silicone sealing ring is set properly in the mouthpiece. Make sure the silicone seal is well-placed before fitting the mouthpiece on the device.

Capping the Cartridge

Step Three: Place the mouthpiece on top of the device, align to the device walls, and press the mouthpiece in until proper closure.

Failure to install the mouthpiece within 1 minute of filling may result in leakage.

Allow For Headspace

Step Four: Check that the mouthpiece is pressed in completely and properly.

Device should be allowed to stand for at least 30 minutes before use. During this time, fluid is priming the atomizer. The rate that the atomizer saturates is dependent upon the viscosity of the fluid. More viscous fluids may require more time.

If the device is to experience a pressure change as a result of an increase in temperature or a change in elevation, the device must be shipped with the mouthpiece facing down, allowing for the inlets to be exposed to ambient air. ​

Previous
Next

Memento™

Fill Instructions

Filling the Reservoir

Step One: Fill a syringe with a short, blunt tipped needle (14 ga. or smaller) with oil. Insert the needle into the space between the airway and the outer walls of the cartridge reservoir. Fill both sides of the cartridge with 0.3mL of oil (0.15mL for each side).

Note: The syringe and needle may need to be warmed to improve fluid flow.

Do not allow fluid to enter the airway (center tube) as it may cause a short circuit.

Checking the Silicone Ring

Step Two: Check the silicone sealing ring is set properly in the mouthpiece. Make sure the silicone seal is well-placed before fitting the mouthpiece on the device.

Capping the Cartridge

Step Three: Place the mouthpiece on top of the device, align to the device walls, and press the mouthpiece in until proper closure.

Failure to install the mouthpiece within 1 minute of filling may result in leakage.

Allow For Headspace

Step Four: Check that the mouthpiece is pressed in completely and properly.

Device should be allowed to stand for at least 30 minutes before use. During this time, fluid is priming the atomizer. The rate that the atomizer saturates is dependent upon the viscosity of the fluid. More viscous fluids may require more time.

If the device is to experience a pressure change as a result of an increase in temperature or a change in elevation, the device must be shipped with the mouthpiece facing down, allowing for the inlets to be exposed to ambient air. ​

Previous
Next

Slym™

Fill Instructions

Filling the Reservoir

Step One: Fill a syringe with a short, blunt tipped needle (14 ga. or smaller) with oil. Insert the needle into the space between the airway and the outer walls of the cartridge reservoir. Fill both sides of the cartridge with 0.3mL of oil (0.15mL for each side).

Note: The syringe and needle may need to be warmed to improve fluid flow.

Do not allow fluid to enter the airway (center tube) as it may cause a short circuit.

Checking the Silicone Ring

Step Two: Check the silicone sealing ring is set properly in the mouthpiece. Make sure the silicone seal is well-placed before fitting the mouthpiece on the device.

Capping the Cartridge

Step Three: Place the mouthpiece on top of the device, align to the device walls, and press the mouthpiece in until proper closure.

Failure to install the mouthpiece within 1 minute of filling may result in leakage.

Allow For Headspace

Step Four: Check that the mouthpiece is pressed in completely and properly.

Device should be allowed to stand for at least 30 minutes before use. During this time, fluid is priming the atomizer. The rate that the atomizer saturates is dependent upon the viscosity of the fluid. More viscous fluids may require more time.

If the device is to experience a pressure change as a result of an increase in temperature or a change in elevation, the device must be shipped with the mouthpiece facing down, allowing for the inlets to be exposed to ambient air. ​

Previous
Next

FAQ

Frequently Asked Questions

No. Liquid X is a single-use, disposable vaporizer platform and does not require recharging. Enjoy!

It depends. Many variables affect how many activations an individual cartridge can provide. Factors include the duration of inhalation and the type of plant-derived extract.

Our cartridges vaporize oil at a consistent rate of 5mg per 3-second draw. Based on this level of consumption, a 0.5mL cartridge would last about 100 draws.

LiquidX contains an oversized battery to ensure full vaporization of the extract before disposal. Battery life depends on how long and how often the device is in use.

All Jupiter Research vaporizers shut off after 10 seconds of inhalation.

Contact Our Team

Instagram has returned invalid data.
Close Menu